Home›Blog›What Temperature Should Hot Water Be in a UK Home?
Boiler Guides
What Temperature Should Hot Water Be in a UK Home?
Reion Miller22 November 2026
In the UK, hot water stored in a cylinder should be kept at 60°C or above to control Legionella bacteria, and should reach your taps at 50°C or more. On a combi boiler, set the hot water dial to about 50–55°C. For radiators, a heating flow temperature of 60°C or below suits most homes with a combi.
I'm Reion Miller, a Gas Safe registered engineer in South London. On service visits I regularly find combis still running at the 70–80°C they were set to on the day they were fitted, and cylinders turned down to save money. The first wastes gas. The second is a health risk. Here are the right settings, what each dial does, and how to change them safely.
Hot Water and Heating Temperatures at a Glance
Setting
Recommended temperature
Why
Hot water cylinder (system or regular boiler)
60°C or higher
Controls Legionella bacteria
Hot water at the tap
At least 50°C
Should arrive within 30 seconds of fully opening the tap
Bath tap in a new-build home
48°C maximum
Building Regulations scald limit
Combi boiler hot water dial
50–55°C
No stored water, so no need to run hotter
Combi heating flow (radiators)
60°C or below
Lets a condensing boiler work efficiently
Room thermostat
18–21°C
UK health guidance recommends at least 18°C in rooms you use
Cold water
Below 20°C
Also helps control Legionella
Hot Water Cylinder Temperature: Why 60°C Matters
Legionella bacteria, which cause Legionnaires' disease, multiply in water between roughly 20°C and 45°C. The Health and Safety Executive's legionella guidance says cylinders should store water at 60°C or higher, with hot water distributed at 50°C or higher and cold water kept below 20°C.
So never turn a cylinder below 60°C to save money. The saving is small, and it keeps stored water in exactly the range bacteria like.
The cylinder thermostat is usually a small dial on the side of the tank, often behind a cover. If it isn't marked, or you're not sure the water reaches 60°C, ask your engineer to check it at your next annual boiler service.
Domestic Hot Water Temperature at the Tap
WaterSafe advises that, where practicable, hot water should reach at least 50°C within 30 seconds of fully opening the tap. Water that hot can scald quickly, especially young children and older people. Two things manage the risk:
Thermostatic mixing valves (TMVs) blend hot and cold water near the tap or bath, so the cylinder stays at 60°C while the outlet is safer.
Building Regulations (Approved Document G) limit hot water at the bath tap in new homes to 48°C, usually with a TMV under the bath.
For a baby's bath, the NHS suggests around 37°C, roughly body temperature. Always mix and test the water first.
Combi Boiler Settings: The Hot Water and Heating Dials
Most combis have two dials: one with a tap symbol for hot water and one with a radiator symbol for heating.
The hot water dial: set it to 50–55°C. A combi heats water on demand instead of storing it, so it doesn't need 60°C. Running it hotter wastes gas, raises the scald risk and speeds up limescale, which matters with South London's hard water.
The heating dial: this is the flow temperature, meaning how hot the water is when it leaves the boiler for the radiators. Set it to 60°C or below. A condensing boiler is most efficient when the water coming back is below about 55°C, because that's when it condenses and recovers extra heat. Nesta's Money Saving Boiler Challenge estimated savings of around £112 a year for a typical combi household at 2022 prices.
Rooms warm a little more slowly at lower flow temperatures, so start the heating earlier. In a hard freeze, going up to 65°C is fine if rooms struggle. If one room never warms up, the radiator may need attention: see why a radiator isn't heating up.
System and Regular Boiler Settings
A system or regular boiler heats your radiators and the coil inside your hot water cylinder, so the two settings depend on each other.
Keep the cylinder thermostat at 60°C. This is the setting that matters for health.
Don't lower the boiler's flow temperature so far that the cylinder can't reach 60°C. If you turn it down for the heating, check the hot water still gets there.
Use the programmer to heat the cylinder at set times, not all day.
Find the right dial using the symbols or the user manual. Never remove the boiler casing.
Change one setting at a time.
Live with it for a few days and check the house warms up and the hot water is comfortable.
Adjust in small steps. If rooms are too cool, go back up 5°C at a time.
Leave the cylinder at 60°C unless an engineer advises otherwise.
Is Your Hot Water Too Hot or Not Hot Enough?
Lukewarm at the tap on a combi: you may be asking for more flow than the boiler can heat (see 25kW vs 30kW combi boilers), or a part such as the diverter valve may be failing.
Scalding water from a tap with a TMV: the valve may have failed. Stop using that outlet and have it checked.
Cylinder never reaches 60°C: the cylinder thermostat, boiler setting or programmer needs looking at.
Landlords: Hot Water Temperature and Legionella
Landlords must assess and control the risk of Legionella in rented homes. Keeping cylinders at 60°C and flushing little-used outlets are central to that. Check hot water temperatures at the same visit as your annual landlord gas safety check: see our gas safety certificate service.
Get Your Settings Checked
Call a Gas Safe registered engineer if the cylinder can't reach 60°C, the boiler won't hold its setting, the hot water temperature swings on its own, or you want the system balanced for lower flow temperatures.
R.W. Miller services and repairs boilers and central heating systems across South London and Surrey. Reion Miller is Gas Safe registered (No. 919881).
Book a boiler service and ask us to check your temperature settings, or call R.W. Miller on 07375 813996.
Stored hot water should be kept at 60°C or higher, and hot water should reach the tap at 50°C or more. Bath water in new homes is limited to 48°C at the tap.
What should I set my combi boiler hot water temperature to?
Around 50–55°C suits most homes. Combis don't store water, so there's no need to run them hotter.
Is it safe to turn my hot water cylinder down to 50°C to save money?
No. Stored water below 60°C can allow Legionella bacteria to grow. If scalding is the worry, fit a thermostatic mixing valve instead.
Does turning down the boiler temperature save money?
Lowering a combi's heating flow temperature usually does, because the boiler condenses more and wastes less heat. Turning down a cylinder saves little and isn't safe.
What temperature is lukewarm water?
Roughly body temperature, around 37°C. That's the temperature the NHS suggests for a baby's bath.
What temperature should my room thermostat be set to?
Between 18°C and 21°C for most people. UK health guidance recommends keeping rooms you use at 18°C or above in winter, especially for older people or anyone with a health condition.
Reion Akim
Gas Safe 919881
Owner / Certified Gas Safe Engineer
Reion Akim is a Gas Safe-registered plumber and heating engineer with 5+ years of hands-on experience across South London. Founded R.W. Miller Plumbing & Heating to deliver honest, high-quality gas and boiler work without the inflated prices. His ethos is simple — actions speak louder than words.